How to Make Your Own Bowling Ball Spinner (Cheapest DIY)
Bowling is a popular pastime enjoyed by millions of people around the world. It requires skill, precision, and a well-maintained ball.
A critical aspect of maintaining a ball is keeping it clean and polished. A bowling ball spinner is a device used to polish the ball and ensure it remains in top condition.
In this article, we’ll show you how to make your own bowling ball spinner, so you can keep your ball in top shape.
What materials and tools are essential for building a homemade bowling ball spinner?
To build a homemade bowling ball spinner, the following materials and tools are essential.
Materials:
- Harbor Freight 5-speed drill press
- 3-quart stainless bowl from Walmart
- Wooden board or steel bar
- Bolts
- Metal bowl
- Rubber washer
- Sandpaper
- Padding material
- Strong timber to make a box and a sheet of wood made with 2×1’s
- Steel angle
- Water pump (you can just get one from a car)
Tools:
- Screwdriver
- Drill
- Saw
- Measuring tape
- Wrench
It is important to note that there are different ways to build a homemade bowling ball spinner, and the materials and tools required may vary depending on the method chosen. However, the above materials and tools are commonly used in DIY bowling ball spinner projects.
Can you provide step-by-step instructions for assembling and using a homemade bowling ball spinner effectively
- Cut out wooden disc: Using a hole saw has great benefits in the next step.
- Glue Wooden disc to bottom of bowl
- Screw the wooden disc to the bowl from the bowl through the wood. Use self-tapping sheet metal screws.
- Use the drill hole from the hole saw as your center mark for the bowl. Make sure the wooden disc is centered well.
- Place washer on the bolt.
- Place the bowl on the washer so the thread sticks out the bottom.
- Place the washer and then the nut on the bolt.
- Tighten as much as possible.
- Optional: Cut tubing down the middle, fit it on the bowl, and cut off excess. Glue to the bowl rim.
- Assemble chuck onto the drill.
- Reduce the drill speed to the lowest by moving the belt.
- Remove the metal lid from the drill press body (optional but recommended).
- Build a 2×4 frame for the drill press top to sit against and attach the drill press to the frame using metal duct strapping.
- Cut out a piece of 2×4 to go inside the frame and press against the drill press housing under the drill shaft. This will remove the last bit of flex from the cheap metal housing. Cut the corners out of the 2×4 to allow for the belt to pass on both sides.
- Clamp the spinner down to a bench or table (make sure you have a cloth or scrap wood under to avoid scratching the surface).
- Put the bolt through the bowl into the chuck.
- Tighten.
- Turn on the drill and hope you found the center of the bowl.
- Tell your dogs they are good boys.
- Enjoy!
Building the Cabinet If you want to build a cabinet for your spinner, you can follow the instructions in the main build link. The cabinet build will require additional tools and materials, such as a scroll saw and lumber. The total cost of building the cabinet is around $125.
What is the rpm of a bowling ball spinner?
The RPM (revolutions per minute) of a bowling ball spinner can vary depending on the model and brand. Here are some examples of RPM ranges for different bowling ball spinners:
- Innovative’s Two Speed Ball Spinner: Low – 400 RPM, High – 600 RPM
- TruCut ½ HP Ball Spinner: 475 RPM
- Donkee Ball Revivor: 580 RPM (low speed), 850 RPM (high speed)
It’s important to note that the RPM of a ball spinner is not the only factor that determines its effectiveness. Other factors such as the motor power, vibration, and adjustability also play a role in how well the spinner can prepare a bowling ball for use.
Conclusion
Building your own bowling ball spinner is a fun and rewarding project that you can do in your spare time. By following this guide, you’ll be able to make your our Own DIY Bowling Ball Spinner.
Resources:
